Push the metal tube through until both ends of it are visible at the end of the fabric. Insert the other tube into the opposite side of the changing table in the same manner. Press the button at the end of the changing table tube which has a button, then insert that tube into the adjacent tube. You will hear an audible snap as it clicks into place.
Insert each of the short metal tubes into the "feet" at the bottom of the changing table, then lower the tubes into the corresponding plastic holes on the corners of the play yard. You will hear another audible snap.
Insert a screwdriver into the back of the vibrator unit to remove the lid. Insert a D battery and replace the lid. Unscrew the lid from the electronics module, insert three AAA batteries and screw its lid into place. Place the newborn napper upside down on a flat surface. Open the vibration unit pocket at the bottom of the napper. Plug one end of the cord into the vibration unit, then place the vibration unit into the pocket.
Close the pocket, leaving one end of the cord loose. Pull the strap on the head support through the matching slot on the newborn napper until the strap is taut. Secure the strap. Locate the snap button on the plastic end of one of the remaining tubes.
Insert the tube into the fabric loop on the newborn napper as you inserted the tubes into the changing table in Step 6, plastic end first. Page 20 7. Insert the button housing tube as shown. Page 21 9. Page 22 The tabs on the sides of the napper will snap in place as shown. Page 23 Napper Mode 1. Press button and pull up unlock and rotate to the napper side.
Push down on the inside of napper until it clicks into place. Check that napper is securely attached by pulling up on it. Do Not print 1. Press button on housing and pull to unlock and rotate to the changer side. Push down on the inside of changer until it clicks into place. Check that changer is securely attached by pulling up on it. Pull up on bassinet clip to detach it from the playard. Repeat steps 1- 2 on the opposite side.
Page 26 4. Make sure to fasten the bassinet clips to the playard as shown. Remove toy bar when baby begins to push up on hands and knees. Recommended use from birth to 5 months. Page 27 1. Attach one end of toybar into center connector. Insert assembled toybar parts into toybar fabric. Attach other end of toybar to center connector. Attach toy to toybar with hook and loop tape. Attach toybar to playard as shown.
Child may use as a step to climb out or reach items in bag. Replace or repair the parts as needed. EBTek Waistpack. EBTek Drawstring Pack. Outside Inside Backpack Shut-The …. Description: One family owned Eddie Bauer pack n play with removable mat that acts as carrying case.
There are three side pockets on one side. Colors include dark blue, dark gray, light blue, light gray.. Fast delivery, full service customer support. Eddie bauer pack and play instruction manual This recall involves the bassinet attachment of the following three different models of Safety 1st and Eddie Bauer Play Yards.
This portable playpen was sold with a bassinet attachment, change station, storage area, and mobile. The convertible play yard has a bassinet and changing station feature.
A mobile with three teddy bears was also sold with the play yard. Models included in the recall are all units and units manufactured before December 1, Check out our eddie bauer pack selection for the very best in unique or custom, handmade pieces from our shops. Try turning it off before starting the app, and only then turn the smartwatch back on.
If all above does not solve the issue, proceed with the following: 1. Delete the application from your phone 2. Delete the unit from the paired devices list in the phone's Bluetooth settings page 3. Restart the phone 4. Perform pairing or factory reset on the unit as described in the troubleshooting section in the user manual — the unit will turn off 5.
Turn the unit back on 6. Pair the unit to the phone via Bluetooth 7. Download and install the app 8. Which mobile app do I need to download for my device?
Connectivity to Smart dashboard, bike infotainment and GPS devices. In order to enjoy the best experience when using a smart system in parallel to a mobile phone we recommend connecting the unit in one of the 2 ways described below: 1. Use a latest model Bluetooth 5. Connect your smartphone to both the bike system and the Cardo unit directly. For all others, bypass the smart dashboard system by connecting both phone and the bike system directly to the Cardo unit one on each channel without connecting the phone to the bike system.
Cardo communication systems can be charged while riding. Simply plug it into the bike's 12V charger or a battery pack. Switch it back on and keep on riding. Do I have to have a phone for it to work? Your intercom and radio features are completely phone independent.
You would need a phone or some other Bluetooth media player to stream music and, of course, to make and receive calls.
What can I do? If you are using a boom mic, make sure your mic is as close to your mouth as possible. Search for the small yellow triangle near the boom and make sure it faces your mouth. If the issue is noise from wind turbulence, put a larger mic sponge on the mic to help reduce it. The larger sponge is included in your package accessories. If you cannot find it you can purchase it as part of a replacement microphone. How do I make sure that my unit's battery lasts as long as possible?
We recommend not to leave your unit unused or in storage for more than 3 months without charging. Be sure to plug your unit at least once every 3 months for full 4 hours to ensure maximum battery life. While your unit comes right out of the box with one of the best set of speakers in the business, you can always plug in your favorite earbuds or aftermarket speakers via the standard 3.
The unit doesn't seem to be charging or the Battery seems to not last as long as it should. Plug in your unit to the charger and leave it charging for at least 4 hours straight. If this does not work, try using a different wall charger and USB cable. DO NOT attempt to disassemble or replace the battery on your own. DO NOT open the unit. It will no longer be waterproof!
That said, we DO NOT recommend replacing parts on your own, for risk of water, dirt and general electronics damage.
0コメント